Secondary Burn Wood Stoves and EPA 2020 Explained
What a secondary burn is, how non-catalytic wood stoves reburn their own smoke, what the EPA 2020 standard requires, and how to run one for high efficiency.
A secondary burn is the difference between a modern wood stove and the smoky box your grandparents ran. It is the reason a current stove can heat the same room on roughly a third less wood while putting far less smoke up the chimney. This page explains what the secondary burn is, how it works, what the EPA 2020 rule demands, and how to actually get one going in your own stove.
What is a secondary burn in a wood stove?
A secondary burn is a second combustion of the smoke that the first fire gives off. When wood burns, about half its energy leaves the log as flammable gases and smoke. In an old stove those gases went straight up the flue unburned, as wasted heat and creosote. A secondary burn stove reignites them inside the firebox so that energy heats your home instead.
You can see it working. Above an established fire, rolling flames appear near the baffle at the top of the firebox, often with no wood directly beneath them. Those are the smoke gases burning in mid air. A clean secondary burn is why a well run modern stove shows almost no visible smoke at the chimney top.
How does secondary combustion work?
Secondary combustion works by adding preheated air to the hot smoke at the top of the firebox. The stove draws outside or room air through channels in its own body, where the fire heats it, then releases it through a row of stainless steel tubes or ports under the baffle. Smoke plus hot air plus enough heat equals a second fire.
Three conditions have to be met at once:
| Condition | What it needs | Why it matters |
|---|---|---|
| Temperature | Secondary zone near 1,100 F | Wood gases do not ignite until roughly 1,100 F; a cool firebox just smokes |
| Oxygen | Preheated secondary air, always on | The smoke needs fresh air to burn; this air is not on the main control |
| Fuel | Wood below 20 percent moisture | Wet wood spends the heat boiling off water, so the firebox never reaches ignition temperature |
The secondary air supply is usually fixed and not connected to the main air control. That is deliberate. You can turn the primary air down to slow the main fire, and the secondary system keeps reburning the smoke that slower fire produces.
What does the EPA 2020 standard require?
The EPA 2020 standard is Step 2 of the New Source Performance Standards, and it caps particulate emissions at 2.0 grams per hour on the crib wood test, or 2.5 grams per hour when a stove is tested with cordwood. It took effect on May 15, 2020, and every new wood or pellet room heater sold in the United States must meet it.
Secondary combustion is how most non-catalytic stoves pass that test. Reburning the smoke removes most of the particulate before it leaves the firebox. A stove that meets the limit carries a permanent metal EPA label on the back and appears in the EPA Certified Wood Heater Database with its tested emissions, efficiency and heat output.
Secondary burn or catalytic: which is cleaner?
On the EPA test data, catalytic and hybrid stoves edge out pure secondary burn designs, but a good secondary burn stove is clean and simpler to own. We pulled the EPA Certified Wood Heater Database in October 2026 and grouped the wood stove rows by combustion type.
| Type | Rows | Median efficiency (HHV) | Median emissions |
|---|---|---|---|
| Non-catalytic (secondary burn) | 92 | 71% | 1.7 g/hr |
| Catalytic | 34 | 78% | 1.1 g/hr |
| Hybrid (both) | 24 | 78.5% | 0.87 g/hr |
Secondary burn stoves have no combustor to wear out and no bypass damper to operate, which is why many buyers still prefer them. The trade-off, and when each type is worth it, is set out in the catalytic versus non-catalytic comparison.
How do you get a secondary burn going?
You earn a secondary burn by getting the firebox hot with the air open, then backing the air down slowly. A cold, choked fire will never reach the ignition temperature the smoke needs, so patience at the start pays off.
- Build and light the fire with the primary air fully open. A top-down fire reaches temperature faster and smokes less at startup.
- Let it establish for 10 to 20 minutes until the firebox is clearly hot and the wood is well caught.
- Reduce the primary air in steps, watching the glass. When the secondary tubes light, flames will roll along the top of the firebox.
- Hold the air at the lowest setting that keeps those secondary flames alive. Go too low and they die and the glass blackens.
Dry wood is not optional here. The seasoning guide explains how to get fuel below 20 percent moisture and prove it with a meter.
Do secondary burn stoves really use less wood?
Yes. A stove that captures the energy in its own smoke delivers more heat per log, so you burn fewer logs for the same warmth. At equal heat delivered, a 71 percent efficient stove burns roughly 9 percent less wood than a 65 percent stove, and the gap against a pre-2020 stove at 50 to 60 percent is far wider.
The caveat is that these figures assume the stove is run correctly. A modern secondary burn stove choked down on wet wood can perform worse than its label, because it never sustains the reburn. Size the stove to your heat load first, using the size and fuel calculator, so you are not forced to smother an oversized firebox all winter.
Which secondary burn stoves perform best?
The strongest non-catalytic rows in the EPA database reach the high 70s for efficiency, which is near the top of what secondary combustion alone achieves. For named models tied to their EPA test rows, see the best wood stoves list, where the non-catalytic picks are flagged against the catalytic and hybrid ones.
As a rule, a secondary burn stove suits a household that burns actively during the day, reloads every few hours and wants a lively flame. It is simpler to live with than a catalytic stove, with no combustor to monitor or replace.
Who should not choose a non-catalytic secondary burn stove?
A pure secondary burn stove is the wrong pick if you want very long, low overnight burns. Secondary combustion fades as the fire dies down and the air is turned low, so these stoves burn best at moderate to high output. For 20 hour plus burns on a single load, a catalytic or hybrid stove holds low heat far better, as the buying guide describes.
It is also the wrong pick if you cannot store and season dry wood, since the whole mechanism depends on reaching ignition temperature. Installation, clearances and venting always follow the stove’s manual, NFPA 211 and a certified installer.
Sources: EPA wood heater NSPS fact sheet, EPA Certified Wood Heater Database, EPA Burn Wise: best wood-burning practices.
Frequently asked questions
Quick answers to what readers ask us most
What is a secondary burn in a wood stove?
It is a second combustion of the smoke. Preheated air entering through tubes or ports above the fire ignites the unburned gases rising off the wood, so they burn instead of going up the flue as smoke and creosote. You see it as rolling flames near the top of the firebox.
Are secondary burn stoves the same as EPA 2020 stoves?
Most non-catalytic EPA 2020 stoves use secondary combustion to meet the standard, so the terms overlap in everyday use. EPA 2020 is the emission rule (2.0 g/hr on the crib test); secondary burn is one of the two combustion methods, alongside catalytic, that stoves use to pass it.
Why will my secondary burn not light?
The usual causes are wet wood, a firebox that is too cold, or the air control choked down too early. Secondary combustion needs the gases above about 1,100 F and plenty of air. Burn wood under 20 percent moisture, let the fire establish with the air open, then reduce it gradually.
Do secondary burn stoves need a catalytic combustor?
No. A secondary burn (non-catalytic) stove reburns smoke with secondary air alone and has no combustor to replace. Catalytic stoves use a coated honeycomb instead, and hybrids use both. See our catalytic versus non-catalytic comparison for the trade-off.