HearthWise Wood and pellet heat, sized and priced with the math shown
Firewood & Pellets

Seasoned Firewood: How to Dry It and Prove It Is Ready

Seasoned firewood reads under 20% moisture on a fresh split. How long wood takes to dry, how to stack and test it, and when kiln-dried wood is worth it.

Seasoned Firewood: How to Dry It and Prove It Is Ready
The short answer Firewood is seasoned when a moisture meter reads under 20% on a freshly split inside face, the EPA Burn Wise target. Split, stacked off the ground and covered only on top, softwood needs at least 6 months and hardwood at least 12, often longer for oak. Kiln-dried wood is dry on arrival but costs far more per cord.

Most wood-stove complaints trace back to the wood. A stove that smokes, will not stay lit, blackens its glass and fills the chimney with creosote is often a stove burning wood that is still wet inside. “Seasoned” is the word sellers use for dry, but the only claim that matters is a number. This page explains the number, how long it takes to get there, how to check it, and when to pay for kiln-dried wood instead.

What makes firewood seasoned?

Firewood is seasoned when its moisture content is under 20%, measured on a freshly split inside face. That is the target the EPA’s Burn Wise program gives: wood burns best below 20% moisture, and you should test it with a wood moisture meter before burning it. Freshly cut wood often holds 50% or more.

“Seasoned” has no legal definition on a firewood ad. A seller can call wood seasoned after six weeks under a tarp. Ask for the meter reading, or take one yourself when the wood arrives.

Why does wet firewood cause problems?

Wet wood spends its heat boiling water before it can burn, and the fire runs cooler and smokier as a result. The EPA’s Burn Wise FAQ explains that unseasoned logs need a lot of energy to drive the water out, which produces more smoke and deposits more creosote in the chimney.

The water alone is a measurable cost. University of Maryland Extension figures put a green cord of red oak at about 4,988 lb and the same cord air-dried at about 3,609 lb. Boiling off that 1,379 lb difference takes roughly 1.3 million BTU, about 5% of the cord’s heat, before counting the cooler, incomplete burn. Creosote is the bigger risk, because it is fuel for a chimney fire. NFPA 211 calls for a chimney inspection every year.

How much water does each species have to lose?

Some species start much wetter than others. The difference between green and air-dried weight per cord, from University of Maryland Extension FS-926 (Table 1), shows how much water each must shed:

SpeciesGreen lb per cordAir-dried lb per cordWater to lose per cord
Ash3,9403,370about 570 lb
Black locust4,6404,010about 630 lb
Sugar maple4,3863,577about 810 lb
Shagbark hickory4,9804,160about 820 lb
White oak4,9423,863about 1,080 lb
Red oak4,9883,609about 1,380 lb
Shortleaf pine4,1202,713about 1,410 lb
American elm4,2932,868about 1,430 lb
Cottonwood3,9202,304about 1,620 lb

Ash starts dry for a hardwood, which is why it is known for drying quickly. Red oak carries more than twice as much water per cord. Water content is only part of the story, since wood structure and piece size also set how fast water escapes. The full heat table for 18 species is on our calculator page.

How long does firewood take to dry?

At least 6 months for softwood and at least 12 months for hardwood, according to the EPA’s Burn Wise storage guidance, with the wood split, stacked off the ground and covered on top. Those are minimums. Dense hardwoods such as oak often need two summers, and HomeGuide notes they can take 2 to 4 years to dry completely.

Climate shifts the timeline. Sun, wind and dry air speed drying; shade, humidity and a pile packed against a wall slow it. That is why the calendar is only a guide. Buy or cut next winter’s wood a year ahead where you can, and confirm with a meter before the first fire.

How should you stack firewood so it dries?

Split it, raise it, give it air, and cover only the top. The EPA’s Burn Wise guidance lists the essentials:

  • Split before stacking. Split pieces dry faster than whole rounds.
  • Keep it off the ground on a base such as rails, pallets or blocks, to cut ground moisture and pests.
  • Cover only the top. Covering the sides traps moisture. A roof with an overhang keeps rain and snow off.
  • Store it outdoors until it is close to burning time.

Stack in rows with space between them so wind can pass through, in the sunniest, breeziest spot you have. The EPA also publishes free plans for simple firewood racks and a woodshed sized from a third of a cord to a full cord. Ready-made racks and sheds are compared by how much of a cord they hold in our firewood racks guide.

How do you test firewood with a moisture meter?

Split a piece and measure the fresh inside face right away. The outside of a log dries first, so a reading on the bark or an old end can look several points drier than the core really is.

  1. Take a few pieces from the middle of the stack, not the top row.
  2. Split each one, and test the freshly exposed face within a minute or two.
  3. Push the meter’s pins in as its manual directs, and read the percentage.
  4. Test three to five pieces and go by the wettest one.

Under 20% means ready. From 20% to 25%, give it more time if you can. Over 25% burns smoky and builds creosote. A basic pin-type meter is enough for firewood. Some meters have species or temperature settings, so read the instructions once.

Without a meter: the EPA says seasoned wood is darker, weighs less and sounds hollow when knocked against another piece. These signs are useful for sorting, not for proving the wood is ready.

Is kiln-dried firewood worth the price?

Kiln-dried firewood is worth it when you need dry wood immediately and burn little of it. It is dried in a heated kiln, so it arrives ready, and it costs far more per unit of heat than air-seasoned wood.

OptionTypical priceHow dryBest for
Seasoned cord, delivered$275-$400 a cord (HomeGuide, 2026)Varies; ask for a readingMain heat, buyers with storage
Green cord$150-$275 a cord (HomeGuide, 2026)50%+ on deliveryBuyers drying a year ahead
Kiln-dried bundles$5-$10 per bundle of up to about 1 cu ft, roughly $640-$1,280 per cord equivalentUsually low; askFireplaces, occasional fires, campfires

“Kiln-dried” has no legal standard, so ask for a moisture figure even on kiln-dried wood. For planning how many cords to buy, see our cord of firewood guide.

Kiln-dried vs heat-treated: what is the difference?

Heat-treated firewood meets a set temperature standard, while kiln-dried does not. The Don’t Move Firewood campaign explains that “kiln-dried” means dried for an unknown time at an unknown temperature and has no legal standing. Heat-treated firewood is produced under a compliance agreement. The most common US standard is 60 C (140 F) at the core for 60 minutes, the approved level for emerald ash borer.

This matters when you travel or buy from far away. Wood labeled only kiln-dried cannot legally leave an emerald ash borer quarantine area. Wood with a USDA APHIS or state heat-treatment seal is usually considered safe to move. Some states, such as New York, set a stricter standard for wood coming in.

Who is this page not for?

This page is about getting wood dry and proving it. It is not a guide to:

  • Buying and measuring a cord, which is in our cord of firewood guide.
  • Choosing a stove, which is in the wood stove buying guide. A modern EPA-certified stove from our picks still smokes on wet wood, and a small stove is even less forgiving.
  • Anyone who cannot store a year of wood. Without covered space for next winter’s supply, plan on buying kiln-dried or tested seasoned wood each year, or consider pellets.

Where do these numbers come from?

The 20% moisture target, the 6 and 12 month seasoning minimums, the storage rules and the signs of seasoned wood come from the EPA’s Burn Wise pages on best burn practices, firewood storage and frequent questions, checked October 6, 2026. Green and air-dried cord weights and heat values come from University of Maryland Extension FS-926, Table 1. The heat needed to boil off water uses the latent heat of vaporization of water, about 970 BTU per pound. Prices come from HomeGuide’s 2026 cord of firewood cost guide. The kiln-dried and heat-treated distinction comes from Don’t Move Firewood, managed by The Nature Conservancy. We did not run drying tests of our own.

Frequently asked questions

Quick answers to what readers ask us most

What moisture content should firewood be?

Under 20%. The EPA's Burn Wise program says wood burns best below 20% moisture and recommends testing it with a wood moisture meter before you burn it. Measure on a freshly split inside face, not on the weathered outside of the log.

How long does firewood take to season?

The EPA's Burn Wise storage guidance says at least 6 months for softwood and 12 months for hardwood, split and stacked off the ground with a roof over it. Dense hardwoods such as oak often need longer, and HomeGuide notes they can take 2 to 4 years to dry completely. The meter, not the calendar, decides.

Can you tell seasoned firewood without a meter?

Roughly. The EPA says seasoned wood is darker, weighs less and sounds hollow when two pieces are knocked together. Those signs help, but they can fool you on wood that is dry outside and wet inside. A moisture meter on a freshly split face is the reliable check.

Is kiln-dried firewood worth it?

It is worth it when you need dry wood now and burn a small amount, such as for a fireplace or a few evenings a week. It costs much more per cord than air-seasoned wood. Kiln-dried is not a legal standard, so ask for a moisture reading. If you need wood that can cross a quarantine line, look for a USDA APHIS or state heat-treatment seal instead.

Should I cover my firewood pile?

Cover the top only. The EPA's Burn Wise guidance says to store wood outdoors, off the ground, with only the top covered, because covering the sides traps moisture. A roof with an overhang that keeps rain and snow off is ideal.