HearthWise Wood and pellet heat, sized and priced with the math shown
Fireplace Inserts

Gas Fireplace Inserts: Direct Vent vs Ventless, and Costs

Converting a fireplace to gas? Direct vent vs ventless inserts, what codes allow, 2026 installed costs, BTU sizing and natural gas vs propane running costs.

Gas Fireplace Inserts: Direct Vent vs Ventless, and Costs
The short answer A gas fireplace insert is a sealed gas firebox that slides into an existing fireplace. Choose direct vent: it takes outside air and exhausts through two liners in the chimney. Expect $2,000 to $5,000 installed on average, and $4,600 to $7,300 for premium models in 2026. Ventless inserts cost less but are restricted by code and not supported by EPA.

A gas fireplace insert turns a drafty wood fireplace into a heater you light with a remote. The decisions that matter are the venting type, the size of the burner, the fuel and the quote. Here is each one with 2026 prices and the code limits that rule out some options before you shop.

What is a gas fireplace insert?

A gas fireplace insert is a sealed steel firebox with a gas burner that fits inside an existing masonry fireplace and vents through the old chimney. It burns natural gas or propane, sits behind glass, and usually has a blower that pushes heat into the room.

It is not the same as a gas log set. Gas logs sit in the open fireplace with the damper open and give little usable heat; HomeGuide prices them at $300 to $2,000 installed. An insert closes off the fireplace opening with a surround panel and is designed to heat the room.

If you have not yet decided between gas, wood, pellet and electric, start with our fireplace inserts guide, which compares all four.

Direct vent or ventless: what is the difference?

A direct vent insert pulls combustion air from outdoors and sends exhaust back outdoors; a ventless insert does both inside the room. That single difference drives cost, code status and indoor air.

Direct vent insertVentless (vent-free) insert
Combustion airOutdoors, through a linerThe room
ExhaustOutdoors, through a second linerInto the room
FrontSealed glassOpen front or screen
Chimney workTwo liners, often 3 inch, to a capChimney sealed or damper closed per manual
Unit price, HomeGuide Feb 2026$2,500 to $3,500 (vented)$700 to $2,500
Code statusAllowed widelyRestricted or banned in some places

Napoleon’s Oakville inserts, for example, ship with vent kits of two 3 inch aluminum liners, one for intake and one for exhaust, joined at a co-linear cap. A direct vent gas fireplace works the same way whether it is an insert or a new built-in unit.

Why do codes and EPA limit ventless inserts?

Because everything the burner produces stays in the house. EPA says it does not support unvented gas stoves and logs because of indoor air quality concerns, and that installing them is illegal in some jurisdictions.

  • California: Health and Safety Code 19881 bars the sale of unvented heaters designed for use inside a dwelling, apart from electric heaters and decorative logs for a vented fireplace. Natural gas unvented logs and fireplaces may be sold only if they meet state-adopted standards and are listed by an approved agency.
  • Model code: the International Fuel Gas Code, section 621, caps unvented room heaters at 40,000 BTU per hour, requires an oxygen depletion sensor, bars them from bedrooms and bathrooms except small wall units, and says they cannot be the only source of comfort heat in a home.
  • Moisture: burning natural gas makes water. By our stoichiometry, one therm produces about 9 lb of water vapor, so a 20,000 BTU ventless insert adds roughly 1.8 lb (nearly a quart) to the room each hour on high.

Vent-free makers advertise near 100% efficiency for the same reason: nothing leaves through a flue.

How much does a gas fireplace insert cost installed?

On average $2,000 to $5,000 installed, per HomeGuide (February 2026), but premium direct vent models sell for more than that average on their own. The insert is $1,500 to $3,500 and labor $500 to $1,500 in HomeGuide’s figures. Retail listings in October 2026 ran higher:

Insert (retail listing, Oct 2026)TypeListed outputPrice range
Majestic Ruby Platinum Medium 30 inDirect ventUp to 27,000 BTU$4,966 to $5,466
Majestic Ruby Platinum Large 35 inDirect ventUp to 32,700 BTU$5,266 to $5,746
Napoleon Oakville GDI3N-1Direct vent, millivoltNot listed$4,106 to $4,321
Superior DRI2027 27 inDirect ventNot listed$3,430 to $3,567
White Mountain Hearth Loft VFLC28INVentless10,000 or 20,000 BTU$2,198 to $2,794
Monessen Solstice VFI33LVentlessNot listed$2,866 to $3,536

Prices are from Fireplaces Direct and vary with the front, liner and ignition chosen. Add $500 to $1,500 labor and a premium direct vent job lands near $4,600 to $7,300 before extra work.

What extra costs can a gas insert quote include?

The gas line and the chimney are the two items that push a quote past the average. HomeGuide’s February 2026 figures for the common add-ons:

ItemTypical cost
Extend an existing gas line to the fireplace$250 to $500
New gas line run$15 to $50+ per linear foot
Stainless steel chimney liner, if required$900 to $3,800
Chimney inspection and cleaning$150 to $375
Chimney repairs found during inspection$500 to $7,000
Carbon monoxide detector$20 to $160

A quote that leaves out the gas line, liner kit, surround and permit is not comparable to one that includes them. Ask for each line item in writing.

How many BTUs should a gas insert have?

Size it to the room or open area it heats, not the whole house. HomeGuide puts gas insert outputs between 10,000 and 60,000 BTU; the direct vent inserts above list 27,000 to 32,700. Check whether a figure is input (gas burned) or output (heat delivered): output is input times efficiency.

An oversized gas insert is less of a problem than an oversized wood stove because the flame turns down, but it can still overheat a small room and cycle on and off. A modulating valve or thermostat remote helps. To estimate what your space needs on the coldest night, run it through our heat load calculator and compare the design load with the insert’s listed output range.

Natural gas or propane: what does each cost to run?

Natural gas costs about half as much per hour as propane. Most inserts come in a natural gas or a propane (LP) version, so you choose at purchase or with the maker’s conversion kit.

FuelPrice used (EIA, Jan 2026)30,000 BTU/hr burner, cost per hourCost per million BTU delivered at 85%
Natural gas$1.35 per thermAbout $0.40$15.85
Propane$2.57 per gallonAbout $0.84$33.01

For comparison, a plug-in electric insert costs about $0.27 an hour at the 2026 average power price but tops out near 5,100 BTU per hour. If you have no gas line and only want light heat, see our electric fireplace inserts guide.

Standing pilot, millivolt or electronic ignition?

Millivolt systems keep the flame working in a blackout; electronic ignition saves the gas a standing pilot burns. A millivolt valve uses a thermopile heated by a standing pilot to make its own small current, so the burner runs without house power. The blower still needs an outlet.

Intermittent pilot ignition (IPI) lights the pilot only when the fire is called for. White Mountain Hearth says its IPI version can run on battery backup during an outage. HomeGuide notes that a pilot assembly left burning all winter may last only 5 to 10 years. If outage heat matters to you, confirm the ignition type on the exact model before you order.

Who should install a gas insert?

A licensed gas fitter or plumber, or a hearth technician certified by the National Fireplace Institute (NFI), working under a permit. Gas piping, the liner, the venting termination and the clearances all come from the insert’s installation manual, local code and NFPA standards, and we do not give installation steps.

Before the insert goes in, the chimney should be inspected and cleaned. Factory-built (zero-clearance) fireplaces are a special case: EPA says they need an insert designed and tested for that specific unit, so many prefab fireplaces cannot take a standard insert. Install a carbon monoxide alarm, and keep the annual service the manual calls for.

Who is a gas insert not for?

Skip it if you have no gas service and do not want propane bills, or if your fireplace is a prefab unit with no listed insert. It is also the wrong pick in these cases:

  • You want heat with no electricity and no fuel delivery: a wood-burning insert works on cordwood alone.
  • Your budget is under about $1,500: an electric insert costs less and needs only an outlet.
  • You want the lowest cost per BTU: cordwood usually beats propane, as our pellet stove vs wood stove comparison shows.
  • You were hoping for ventless in a bedroom or as whole-home heat: the model code does not allow it.

Where do these numbers come from?

Frequently asked questions

Quick answers to what readers ask us most

What is the difference between a direct vent and a ventless gas insert?

A direct vent insert is sealed behind glass, pulls combustion air from outdoors and sends exhaust outdoors through two liners run up the chimney. A ventless (vent-free) insert takes air from the room and releases all of its combustion products, including water vapor, into the room. Direct vent is the type EPA supports; it does not support unvented models.

Are ventless gas fireplace inserts legal?

It depends on where you live. California Health and Safety Code 19881 bars the sale of unvented heaters for use in a dwelling, apart from electric heaters and decorative logs for a vented fireplace, and allows natural gas unvented logs and fireplaces only under state-adopted standards with an approved listing. EPA notes they are illegal to install in some jurisdictions. Where they are allowed, the International Fuel Gas Code limits their size and where they can go. Ask your local building department before you buy.

How much does a gas fireplace insert cost to install?

HomeGuide puts the average at $2,000 to $5,000 installed in February 2026: $1,500 to $3,500 for the insert and $500 to $1,500 for labor. Premium direct vent inserts listed at $4,100 to $5,750 in October 2026, which puts a finished job near $4,600 to $7,300 before any gas line or chimney repair.

Is it cheaper to run a gas insert on natural gas or propane?

Natural gas, by about half. A 30,000 BTU per hour burner costs about $0.40 an hour on natural gas at $1.35 a therm and about $0.84 an hour on propane at $2.57 a gallon, using US residential averages from EIA for January 2026.

Does a gas fireplace insert work during a power outage?

Many do. A millivolt valve with a standing pilot makes its own small current, so the flame runs without house power, though the blower will not. Some electronic-ignition models run on battery backup. Check the manual of the model you are considering.